7/23/2023 0 Comments Apple configurator invalid profileOnce the iPad joined the HotSpot, it bypassed all prompts and it went directly to Remote Management. I went a few screens back to Wi-Fi and changed it to use my HotSpot. Then I get Remote Management, followed by an error: The Configuration for your iPad could not be downloaded. + Apps & Data (for Migration) (my AirWatch DEP Profile is set to bypass it) + Passcode (my AirWatch DEP Profile is set to bypass it) + Touch ID (my AirWatch DEP Profile is set to bypass it) + Showed Data Privacy (my AirWatch DEP Profile is set to bypass it) Using same company SSID used for device provisioning. Next, try manual process, as opposed to Automator. (Domain: MCCloudConfigErrorDomain Code: 33001) cfgutil: error: The configuration is not available. (Domain: MCCloudConfigErrorDomain Code: 33001). The Action: ' Prepare Devices Using Automated Enrollment' encountered an error: ' cfgutil: error: The Configuration is not available. (Using company SSID for device provisioning, been using it for 2 years.) Started Automator workflow process to enroll devices.ģ) Prepare Devices Using Automated Enrollment. In DEP, I assigned device to the correct MDM Server. Jeremy, et all - this is what I just tried.ĪW: Groups & Setting -> All Settings -> Devices & Users -> Apple -> Device Enrollment ProgramĪW: Uploaded Server Token and Completed AW configuration as usual. When you try to provision again without a full device wpie (Erase All Content And Settings), the serial number check has already been done and therefore the device activation record is already set.Įrasing all Content and Settings reset the activation record, forcing the iPad to go back to the Apple servers. These steps work for me and this is the reason I believe why.Ī device enrollment was attempted, however it failed becuase the device was not yet discoverd by AirWatch. What to do? In Apple Configurator 2, Version 2.9 (3J40) > Anything other than 'Unactivated' will make it fail. Once you can see the serial numbers under the Enrollment Status page, continue:ġ) connect the iPad to a mac os client running Apple Configuator.Ģ) When the device is connected, what is the activation status? If the serial numbers are NOT listed, do this: Devices listed under Enrollment status, Yes, OK. Does anybody have any suggestions that might be helpful?ĪPNs, good. It isn't affecting iOS device that are already enrolled just new enrollments. I've tried renewing the APNS cert as well as the DEP cert, even though neither were expired, I've verified that the firewall is open and allowing all Apple traffic. 9th for this issue and I'm lucky if I can get support to respond to an email once a day so I'm coming here for help. I've had a support ticket open since Aug. Today I upgraded to version 1907 and the issue still remains. I did the patch and it installed successfully but the error still persisted. At the time we were on version 9.6.0.8 and support suggested installing a patch to version 9.6.0.25. This happened on DEP devices assigned to the AirWatch server, DEP devices not assigned to the AirWatch server, and non-DEP devices. Invalid profile.' when enrolling iOS devices. Please ensure that your iOS devices have network connectivity before managing them using Apple Configurator.A couple of weeks ago we started seeing the message, ' The configuration for you iPad/iPod/iPhone could not be downloaded. Because pushing the Meraki management profile is a part of the refresh process for supervised devices, this process will fail if the device does not have connectivity to the Internet. One of the most commonly reported scenarios is when an administrator attempts to refresh a set of supervised iOS devices using Apple Configurator. Ensure that all traffic to/from is unrestricted Ensure that your network firewall does not block the Simple Certificate Enrollment Protocol (SCEP), which runs over HTTPS. The iPad is joined to a network and can access the internet This happens when the iPad does not have network access, and cannot verify the profile that you're trying to push with Apple Configurator. To remedy this, ensure that: Unlock device and try again." UserInfo=0x7fcc2c0d65a0 (/SourceCache/AppleConfigurationUtility/AppleConfigurationUtility-110/Application/Controllers/CDDeviceController.m:445) : ERROR - 1628230ms Apply policy of UDID:1fe6bbe45dc3073ef6a18239f1a8cb857016eb80 failed: Error Domain= Code=5026 "Unable to install configuration profile. In Console.app, the following message will be logged:Ħ/11/12 9:01:41.124 AM. In some cases, the Systems Manager profile fails to install on an iOS device with an error "Can't install profile."
0 Comments
Leave a Reply. |